Ý tưởng về một bộ dụng cụ tiện lỗ vuông,lỗ lục giác
137,822
Published 2024-03-03
All Comments (21)
-
-
Video cho tôi thấy khả năng của bạn, tôi thích video này tôi không áp dụng nên tôi thấy nói hiệu quả 90% 10% còn lại chờ video chỉnh sửa lại thiết bị đóng. Like cho bạn
-
Ko hiểu lắm. Hay do thiếu sót video nhỉ. Mặc dù rất nhỏ, nhưg trong video tất cả đều quay tiện đồng tâm. Vậy khúc nào tạo ra góc nghiêng cho mũi dao nhỉ.
-
Bị giấu mất 1 bước nào rồi chứ đồng tâm thì k bao giờ ép nổi sắt
-
Quá tuyệt vời luôn em ơi
-
Robisz fajne rzeczy ale ten pomysł źle skopiowałeś. żeby działało prawidłowo narzędzie musi być pochylone bo w tej chwili to masz stempel i prasę postaci konika - wyłącz obroty i uzyskasz ten sam efekt. powodziowo narzędzie powinno wybierać bokami wykonując ruch podobny do bujania się - zwykle oś jest pod kątem o 1.3-1.5 stopnia
-
Hay quá mới mẻ mà lạ quá 👍👍👍👍
-
Hay qua anh...thich thât
-
Nhìn phê thật, khá cầu kỳ cho 1 bộ dụng cụ😊
-
bạn giỏi quá !:face-red-heart-shape::face-red-heart-shape::face-red-heart-shape:
-
Theo nguyên lý chuyển động thì mâm cập với mũi lục giác quay cùng tốc độ. Nên tốc độ tương đối của 2 cái này là 0. Vậy nó ý như anh để yên anh đẩy mũi lục giác vào. Chả có chuyển động cắt nào.
-
Hay quá bạn ơi
-
Hay lắm anh
-
Nice work. Using hardened steel to cut into aluminium could presumably be done with a hammer. Cutting into steel is often done with a wobble broach. That is, as the cutter moves forward it is eccentric and rotates, it pushes on one corner then the next and so on as it rotates. This makes it easier to swage harder steels. The relief behind the cutting face is also important and can be seen but it was not emphasised.
-
Theo mình là lúc làm cái lỗ bạc đạn nên làm lệch tâm vài % sẽ ko bị kẹt mũi.
-
Hi, you are nearly there! Concave the cutter tip a bit to add relief and then add a one degree offset. The cutter needs to oscillate (precession) to cut effectively, it's not just a ram it in there job. That's why your work slipped under pressure. If the hole for the bearings was one degree off true it would work better. See this old tonys video "Rotary Broach: captains log supplemental" and you'll see the action of the cutter. Not a bad effort though 😉 Enjoying your videos 👍
-
Есть похожее видео по ротационной прошивке, но вся суть в том, чтобы закосить голову относительно конуса, сделать с биением торцевым. Тут этого нет
-
يا أخي فيديوهاتك إدمان و متعة رائعة واصل نحن دائما نتابعك تقبل تحياتي الخالصة.👍👍👍👍👍👍
-
Ничего не понял. Обычная прошивка без эксцентрика. Зачем тут станок и вот это всё? С таким-же успехом можно просто надавить задней бабкой, или ударить молотком без всякого вращения. Вращение нужно для прошивок с эксцентриком
-
Chưa hiểu vì sao nó lại xoay tròn mà kô phải đục vì mình làm cạnh lục giác hay tứ giác chứ kô phải chạy răng tròn